General

• save : Saves configuration
• pwr mode : Power mode
• ctm15x : Command for configuration of protected values

Serial Port Settings

• freeconsole : Kill serial console prompt
• mode : Sets serial port(s) connection mode
• port : Serial port settings
• ppp : Local Point to Point Protocol connection

Local\Remote Access

• rmtd : Reverse telnet connection
• access autologin : set auto-login on serial console
• access password : set login password for SSH, Telnet, Web, Console
• access sessiontimeout : session timeout value
• access cell ftpport : configure FTP port on Cellular interface
• access cell httpsport : configure HTTPS port on Cellular interface
• access cell sshport : configure SSH port on Cellular interface
• access cell telnetport : configure Telnet port on Cellular interface
• access cell webport : configure HTTP (Web) port on Cellular interface
• access lan0 ftpport : configure FTP port on LAN0 interface
• access lan0 httpsport : configure HTTPS port on LAN0 interface
• access lan0 sshport : configure SSH port on LAN0 interface
• access lan0 telnetport : configure Telnet port on LAN0 interface
• access lan0 webport : configure HTTP (Web) port on LAN0 interface
• access lan1 ftpport : configure FTP port on LAN1 interface
• access lan1 httpsport : configure HTTPS port on LAN1 interface
• access lan1 sshport : configure SSH port on LAN1 interface
• access lan1 telnetport : configure Telnet port on LAN1 interface
• access lan1 webport : configure HTTP (Web) port on LAN1 interface
• access wlan ftpport : configure FTP port on WLAN interface
• access wlan httpsport : configure HTTPS port on WLAN interface
• access wlan sshport : configure SSH port on WLAN interface
• access wlan telnetport : configure Telnet port on WLAN interface
• access wlan webport : configure HTTP (Web) port on WLAN interface

Wireless Networks

• data : Query count of data transmitted/received over wireless link
• satbackup : Switch to backup satellite modem

Cellular

• apn : Set APN for cellular carrier.
• pin : Set 4-digit SIM card PIN code for cell devices (if required)l
• autoconnect : Auto network connection
• device cell : Configure cell device
• device cellmtu : Configure MTU for the cellular interface
• device cellnetwork : Configure cell device to use a specified network type
• device lteband : Configure cell device to use a specified LTE band
• dnscheck : Check valid DNS
• otasp : Over-The-Air Service Provisioning
• dir : Set NAM phone number,MDN,MIN
• esn : Query the serial number (ESN/IMEI) of the wireless device
• modemid : Assign device ID
• ratesel : Rate select for Sierra Wireless CDMA/EVDO data devices/modules only
• ratetmr : Rate Timer, Sierra Wireless CDMA/EVDO only
• rssi : RF signal strength
• spc : Service provisioning code
• univwd : Configure universal watchdog
• univwdtimer : Set universal watchdog timer interval
• mip : Mobile IP
• pswd : Sets password used for wireless network access via simple IP
• user : Sets username used for wireless network access via simple IP

SMS

• sms enable : SMS configuration access
• sms fwdreport : Configure forwarding of incoming SMS messages
• sms friends : Set friends list for SMS commands

Wi-Fi Networks

• device wifi : Configure Wifi device
• device priority : Configure priority for dual-mode cellular/wi-fi configurations.
• wlan enable : Configure device for:cellular,cellular+wi-fi client, cellular+wi-fi AP
• wifi country : Set the wireless regulatory country code
• wifi watchdog : Configure wireless watchdog
• wifi mac : Query the wireless MAC address

Wi-Fi Client

• wifi client channel : Set the wireless channel
• wifi client eap : Sets the wireless client EAP mode
• wifi client encryption : Sets the wireless encryption type
• wifi client hwmode : Set the wireless hardware mode
• wifi client key : Set the wireless key
• wifi client ssid : Sets the wireless SSID
• wifi client scan : Scans for wireless
• wlan gw : Configure a default gateway IP address for the wifi client interface
• wlan ip : Configure a static IP address for the wifi client interface
• wlan mtu : Configure MTU value on the wifi client interface
• wlan netmask : Configure the IP address netmask for the wifi client interface
• wlan proto : Configure the network protocol for the wifi client interface

Wi-Fi Access Point

• wifi ap channel : Set the wireless channel
• wifi ap encryption : Sets the wireless encryption type
• wifi ap hwmode : Set the wireless hardware mode
• wifi ap ignorebcast : Set wifi AP to not broadcast SSID
• wifi ap isolate : Isolate wifi clients from each other.
• wifi ap key : Set the wireless key
• wifi ap ssid : Sets the wireless SSID
• wifi ap macaddrallowadd :add a MAC address to wifi allow list
• wifi ap macaddrallowdel :remove a MAC address from wifi allow list
• wifi ap macaddrdenyadd :add a MAC address to wifi deny list
• wifi ap macaddrdenydel :remove a MAC address to wifi deny list

Captive Portal

• enable :enable captive portal
• nasid :set captive portal NAS ID
• uamport :set UAM port
• radserver1 :set RADIUS server 1 address
• radserver2 :set RADIUS server 2 address
• authservurl :set authentication server URL
• uamsecret :set UAM secret
• radsecret :set RADIUS secret
• radauthport :set RADIUS authentication port
• radaccport :set RADIUS accounting port
• whitelist :set whitelist
• domains :set domains (dynamic whitelist)
• sessiontimeout :set session timeout
• idletimeout :set idle timeout
• bwdown :set download bandwidth
• bwup :set upload bandwidth

Bluetooth

• bt console : Enable/disable Bluetooth console mode
• bt enable : Enable/disable all Bluetooth functions
• bt ble : Enable/disable scanning Bluetooth Low Energy
• bt blemax : Set the maximum number of BLE devices being tracked
• bt blestale : Sets when each BLE data is considered stale and to be removed
• bt ip : Set the local IP for Bluetooth NAP
• bt name : Set the local Bluetooth device name
• bt pin : Set the local Bluetooth device password
• bt nap : Enable/disable Bluetooth NAP mode
• bt obd : Enable/disable Bluetooth OBD mode
• bt remname : Set the remote Bluetooth device name
• bt rempin : Set the remote Bluetooth device password

Satellite

• sat enable : Set satellite mode
• sat force : Force satellite to be enabled in dynamic mode when Pendant PANIC messages are sent
• sat mt : Minimum time between identical report numbers when using satellite
• sat pwr : Enable/disable satellite when satellite is in dynamic mode
• sat ip : Set the remote server IP to send received sat msgs that are not $cmd msgs to
• sat port : Set the remove server port to send received sat msgs that are not $cmd msgs to
• sat stats : Show satellite status
• sat flush : Clears outbound satellite messages
• sat reset : Clears the satellite tx/rx info

SNMP

• snmp enable : Enable SNMP
• snmp rwcommunity : Set the RW community
• snmp rocommunity : Set the RO community
• snmp trapcommunity : Set the Trap community
• snmp traphost : Set the Trap IPv4 address
• snmp trapversion : Set the Trap version
• snmp v3user : Set the v3 user
• snmp v3access : Set the v3 user access
• snmp v3authpass : Set the v3 authentication passphrase
• snmp v3privpass : Set the v3 privacy passphrase
• snmp v3security : Set the v3 security
• snmp v3authtype : Set the v3 authorization type
• snmp v3privtype : Set tv3 privacy type
• snmp v3authfailtrap : Enable v3 authorization fail trap

Power Management

• pwr accelt : Wake on acceleration condition
• pwr geofence : Geofence threshold
• pwr rtc : RTC (real-time clock) threshold
• pwr sdwn : Power shutdown
• pwr speedth : GPS speed threshold
• pwr temp : Temperature threshold
• pwr vcct : Supply voltage threshold
• pwr woe : Power wake on event

Time Synchronization

• gpstime : Set priority of valid GPS as system time synchronization source
• networktime : Set priority of cellular network time as system time synchronization source.
• ntpserver : Set URL or IP of NTP server for system time synchronization
• ntptime : Set priority of NTP client as system time synchronization source
• timesync : Set period for system time synchronization
• timezone : Set system timezone

Firmware Upgrade and Configuration

Device Management

• confdrop : Drop a backup configuration onto a CTM-200
• confupgrade : Configures the device for automatic configuration capability
• stm upgrade : Upgrades STM/Mini Micro FW
• upgradefw : Upgrade firmware image
• upgradesrv : Set authorized IP for remote admin

SNMP

• snmp : Configure SNMP server

VUE

• vue ack : Run the VUE client/server acknowledgement
• vue port : Configure TCP server port for device
• vue pwrup : Configure VUE client to run on power up
• vue remip : Configure IP address of remote VUE server
• vue remport : Configure TCP port number of remote VUE server
• vue service : Configure VUE service

Networking

LAN

• ethernet : Enable/disable LAN client Internet services.
• ctm15x : Command for configuration of protected values
• lanbridge : Bridge LAN ports
• langw : LAN Gateway IP address
• lanip : IP address of device on LAN
• lanmtu : Configure MTU on LAN interface
• lannat : Enable SNAT on LAN interface
• lannetmask : Netmask of device on LAN
• lanproto : Set interface prototype to static or dhcp
• multiwan enable : Enable multiwan configuration
• multiwan mode : Select multiwan mode type

Authentication

• authport : Set the port number for a Radius authentication server
• authsecret : Set the shared secret for a Radius authentication server
• authserver : Set the IP address for a Radius authentication server
• lan8021x : Set 802.1x LAN authentication

DHCP

• landhcp : LAN DHCP server settings

DNS

• net staticdns : Define static DNS server IP addresses
• net dnssource : Sets permitted sources from which to accept DNS server IP addresses
• dynhost enable :enable/disable local DNS lookup
• dynhost set :configure local DNS lookup

DynDNS

• dyndns : Dynamic DNS

DMZ

• dmz : Demilitarized zone (DMZ) feature

Port Forwarding

• firewall : Configure firewall – port forwarding

Friends list

• lanfriends : Control ethernet access control using MAC addresses.
• friends : Set firewall friends list

Message Redirector

• msgredirect add : Add a redirect IP address / port
• msgredirect del : Delete a redirect IP address / port
• msgredirect enable : Enable/disable message redirect application
• msgredirect list : List redirect entries
• msgredirect port : Configure message redirect listening port
• msgredirect remip : Restrict incoming redirect messages to a specified remote source IP

Half Bridge

• modemmode : Enable Modem Mode/Half Bridge mode
• modemmodedhcp : Enable DHCP support with Modem Mode
• clientmac : Set client mac address for modem mode with DHCP

Static Routes

• staticroute : Configure static routes.

Network Watchdogs

• netwd : Network watchdog
• univwd : Configure universal watchdog
• univwdtimer : Set universal watchdog timer interval
• wifi watchdog : Configure wireless watchdog

Vehicle Support

Engine Diagnostics Support

• can apply : Set STM with values set in cmd engparam and can prot
• can baud : Set CAN baud rate
• can std : Set CAN header type
• can showdata : Shows a list of unique received CAN data
• can subsys : Set CAN subsystems to use
• can senddiag : Set how often diagnostic session is requested
• can errmax : Set number of sessions with CAN errors when CAN is no longer attempted
• can engparam : Set which parameters are to be queried/reported
• can prot : Enable/disable internal CAN and sets the protocol
• can usbprot : Sets the protocol to use with USB CAN
• can vtype : Set the specific vehicle model to be used with CTM
• can qryrate : Sets the CAN querying rate
• can psthruid : Set CAN header/ID to look for by canpsthru ps
• can psthrumin : Set minimum time for each CAN header/ID passed by canpsthru ps
• can enghours : Set source of engine hour data
• can odometer : Set source of odometer data
• odometer : Odometer
• enghours : Calculate engine hours
• ctm15x : Command for configuration of protected values
• enghrmode : Used to configure enghours command
• obdcond : OBD report trigger conditions
• obddata : Display data obtained from OBDII transmitter
• obdsp : Sets protocol used by OBDII transmitter
• obdreport : Set report for OBD trigger
• obdlistload : Load parameter list used by pobdx
• pobda-pobdh : Configure OBDII reports

VIN

• vin pwrup : Configure VIN lookup tool to run on power up
• vin server : Configure IP address of repository
• vin port : Configure TCP port of repository
• vin ssl : Configure to use HTTPS or HTTP for accessing repository
• vin query : Manually execute the VIN lookup tool
• vin clear : Delete the recipes downloaded by the VIN lookup tool

Acceleration

• orientation : Set device mounting orientation for use with accelerometer sensor
• accel altvalidmax : Set maximum allowable change in altitude before GPS module is reset
• accel cond : Set acceleration trigger condition
• accel gpscoef : Set the minimum GPS vs accelerometer or OBD speed based acceleration required
• accel gpsobddiff : Set the maximum allowable difference between GPS and OBD speed to prevent accel gpsmaxspeed and accel validmax checks
• accel history : Enable/disable historical GPS&OBD report used for acceleration calculation
• accel historydelay : Set the delay between each historical GPS&OBD report
• accel historynum : Set number of historical GPS&OBD report to generate
• accel maxgpsspeed : Set maximum allowable GPS speed before GPS module is reset
• accel report : Set acceleration report
• accel rollcond : Set rollover trigger condition
• accel rollrep : Set rollover report
• accel sensor : Set sensor used for triggering longitudinal acceleration
• accel validmax : Set maximum allowable GPS acceleration before GPS module is reset

Fuel Rate

• fuel io : Configure GPIO for fuel calculation
• fuel tank : Configure fuel tank size and reading settings
• fuel maxspd : Set the maximum speed to use fuel level
• fuel mode : Set the fuel mode
• fuel query : Query the total fuel value
• fuel rate : Set the fuel rate distance for fuel rate calculation
• fuel rate query : Query the fuel rate
• fuel rate reset : Reset the fuel rate
• fuel reset : Reset the total fuel value
• fuel dev : Set the maximum allowable standard deviation for fuel level
• fuel refuel : Set the percent fuel increase to consider refueling has occurred

Idle Time

• idle cond : Set the idle condtion
• idle mode : Set the idle mode
• idle report : Set report for idle conditon
• idle query : Query the idle time
• idle reset : Reset the idle time
• idle time : Set the idle time

General Purpose I/O

• dout : Set/query digital outputs
• doutrestore : Set digital outputs to restore on boot
• input : Query input channels status
• insetup : Input setup
• pulse coef : Set the pulse rate coefficient multiplier
• pulse edge : Set whether pulse counting uses edge detection or voltage threshold
• pulse input : Set voltage threshold for pulse counting
• pulse period : Set whether pulse rate is to be calculated
• pulse pwm : Enable/disable PWM detection
• satbackup : Switch to backup satellite modem

GPS Configuration

• agpspde : Configure Assisted GPS (A-GPS) using cellular device location based features
• gpsdata : Display status of GPS input devices
• gpsdgps : Enable DGPS mode and SBAS
• gpscache : Enable using cached GPS position
• gpsdop : Set GPS DOP filtering
• gpsgga : GPS GGA message
• gpsinput : GPS input device, internal on board GPS module, external GPS device or Cellular based A-GPS
• gpsparam : GPS port configuration and priority
• gpspos : Set fixed GPS position
• gpsrmc : GPS RMC message
• nmeamode : Set NMEA 0183 version for GPGLL and GPRMC sentences
• odometer : Odometer
• ctm15x : Command for configuration of protected values

Reports

• autopevent : Turns on $PEVENT message reporting of trigger/event description
• sendreport : Generates and sends a "One-Shot" report upon execution of the command
• tcppersist : Set persistent TCP report connections

Store and Forward

• snfdelay : Store and Forward delay period before SNF starts
• snfflush : Store and Forward Flush
• snflog : Store and Forward log
• snfonsd : Configure SNF to use SD card storage

GPS Reports

• gpsaddmes : Add GPS messages to a report
• gpscond : GPS report trigger conditions
• gpsdelmes : Delete GPS message
• gpsemail : GPS email address
• gpslocip : GPS local IP address
• gpslocport : GPS local port
• gpsmes : GPS messages
• gpsremip : GPS remote IP address
• gpsremport : GPS remote port
• gpsrep : GPS reporting
• gpssms : Set destination of GPS SMS report
• emailsrv : Set email server
• reportscripts : Configure custom scripts to be triggered when reports are generated

Input\Output Reports

• insetup : Input setup
• ioaddmes : Add IO message
• iocond : IO report trigger conditions
• iodelmes : Delete IO message
• ioemail : IO email address
• iolocip : IO local IP address
• iolocport : IO local port
• iomes : IO messages
• ioremip : IO remote IP address
• ioremport : IO remote port
• iorep : IO reporting
• iosms : Set destination of IO SMS report
• emailsrv : Set email server
• reportscripts : Configure custom scripts to be triggered when reports are generated

General Reports

• emailsrv : Set email server
• lanrepip : LAN IP address for local reporting
• repaddmes : Add messages to a report configuration, display report configuration messages
• repdelmes : Delete messages from a report configuration
• repemail : Configure report email address
• replocip : Configure report local IP address
• replocport : Configure report local port
• repremip : Configure report remote IP address
• repremport : Configure report remote port
• repsms : Configure report SMS address
• reptype : Configure local and remote report types, store-and-forward
• reportscripts : Configure custom scripts to be triggered when reports are generated

Reports linked with 'General Reports'

File Based Reports

• repfiledelivery : Configure delivery parameters for file-based reporting
• repfiledir : Configure main folder for file-based reporting
• repfilename : Configure filename for file-based reporting
• repfileout : Configure outbox folder for file-based reporting
• repfilesize : Configure maximum file size for file-based reporting
• repfiletimestamp : Configure timestamp added to data files for file-based reporting
• repfilezip : Configure compression of data files for file-based reporting
• sshkey : Generate a SSH key

Ignition Reports

• igncond : Ignition report trigger conditions
• ignreport : Set ignition trigger report

Power-up Reports

• pupcond : Power up report trigger conditions
• pupreport : Set power up report

VCC Reports

• vcc : Supply voltage
• vcccond : Supply voltage level report trigger conditions
• vccreport : Set supply voltage level report

Acceleration Reports

• (Refer to Vehicle Support|Acceleration section)

Data Reports

• data : Query count of data transmitted/received over wireless link
• datacond : Wireless link total data count trigger condition
• datareport : Set the link data report(s)

Idle Reports

• (Refer to Vehicle Support|Idle Time section)

OBD Reports

• (Refer to Vehicle Support|Engine Diagnostics Support section)

MODBUS Reports

• (Refer to MODBUS section)

Swipe Reports

• (Refer to Special Features|RFID/Card Reader Support section)

Event Reports

• (Refer to Diagnostics and Logging|Event Log Configuration section)

Geo-Route Reports

• (Refer to Special Features|Geo-Routing section)

Man Down Pendant Reports

• (Refer to Man Down Pendant section)

Salt Reports

Auxiliary Reports

• saltreport : Set salt-spreader report
• aux ack : Sets the ack character sequence for mode 24
• aux authtype : Sets the authentication mechanism used with auxiliary device
• aux checksum : Sets the value used for checksum calculation
• aux cond : Sets the triggering conditions for mode 23/24
• aux conf : Sets the reporting configuration for mode 23/24
• aux datatype :sets the data type of the auxiliary device payload
• aux dev : Sets the auxiliary device name for mode 23/24
• aux lead : Sets the leading characters for mode 24
• aux leadlen : Sets the number of leading characters for mode 24
• aux lead2 : Sets the secondary set of leading characters for mode 24
• aux lead2len : Sets the number of characters in the secondary set for mode 24
• aux leadmode : Sets the leading characters matching criteria for mode 24
• aux leadterm : Set to use leading or terminating characters or both for mode 24
• aux len : Sets the payload length for mode 23/24
• aux mode : Sets the specific processing method for mode 23/24
• aux pollnow : Tells CTM to poll the auxiliary device for mode 23
• aux pollstr : Sets the polling string for mode 23
• aux polltim : Sets the polling timeout for mode 23
• aux repmode : Sets whether to append payload to ASCII (msg 114) or binary (msg 112) header
• aux report : Sets the reports to be used for mode 22-23
• aux rmleadterm : Set to remove leading or terminating characters or both for mode 24
• aux term : Sets the termination characters for mode 22/24
• aux termlen : Sets the number of termination characters for mode 22/24
• aux timeoutsend : Sets whether data is sent out when serial input times out for mode 22/24
• mode : Sets serial port(s) connection mode

TAIP Reports

• taipchecksum : Enable/disable checksum in TAIP messages
• taipid : Set TAIP ID
• taipuseid : Enable/disable reporting of ID in TAIP messages

Boom Reports

• boomreport : Set the boom tracker report(s)

PCYP Reports

• pcyp key :pcyp key
• pcyp key add :add a new pcyp key
• pcyp key del :del a new pcyp key
• pcyp key view :view pcyp keys

• pcyp value :pcyp value
• pcyp value add :add a new pcyp key/value
• pcyp value del :del a new pcyp key/value

• pcyp delimiter :pcyp delimiter
• pcyp replace :pcyp replace

• pcyp msg :pcyp msg
• pcyp msg add :add a key to a pcyp msg
• pcyp msg del :del a pcyp msg or a key within a pcyp msg
• pcyp msg view :view pcyp msg keys
• pcyp msg replace :replace a key in a pcyp msg
• pcyp msg query :query pcyp msgs

IoT

• iot mqtt_enable :enable MQTT/IoT reporting
• iot azure connection_string : set Microsoft Azure device connection string
• iot watson auth_token :set Watson IoT device authentication token
• iot watson orgid :set Watson IoT organization ID
• iot watson mode :set Watson IoT data report mode

MODBUS

• mode : Sets serial port(s) connection mode
• modbusmode : Sets the MODBUS gateway mode

MODBUS MASTER

• mbusm add : Add MODBUS slave in MODBUS master mode
• mbusm cond : Sets reporting conditions for MODBUS master mode
• mbusm data : Shows current MODBUS slave register values for MODBUS master mode
• mbusm del : Remove MODBUS slave in MODBUS master mode
• mbusm exccond : Sets condition to trigger MODBUS exception reports for MODBUS master mode
• mbusm excreport : Sets reports to be used for MODBUS exception triggered reports
• mbusm poll : Sets polling MODBUS slaves while in MODBUS master mode
• mbusm report : Sets reports to be used for MODBUS master triggered reports

MODBUS GATEWAY

• freeconsole : Kill serial console prompt
• modbusadd : Add a MODBUS TCP slave, serial slave or self slave, query MODBUS slave gateway list
• modbusctm130 : Enable backward compatibility with CTM-13X MODBUS messages over-the-air
• modbusdel : Delete MODBUS entry
• modbusgw : Manual MODBUS gateway initiation
• modbusidmap : Set up MODBUS ID to device IP:port map
• modbusport : Sets the MODBUS port number
• modbussecure : Secure MODBUS for use with SSH tunneling

PAD

• freeconsole : Kill serial console prompt
• gopad : Enable either 1 or 2 instances of PAD
• mode : Sets serial port(s) connection mode
• pad clientport : PAD client port number for dialup emulation modes
• pad echo : PAD echo mode
• pad esc : PAD escape sequence
• pad esct : PAD escape guard time
• pad fifo : PAD fifo
• pad fwdc : PAD forwarding character
• pad fwdl : PAD forwarding length
• pad fwdt : PAD forwarding time
• pad ip : PAD IP address
• pad mode : PAD mode
• pad pfc : PAD postfix character
• pad port : PAD port number
• pad reset : PAD reset
• pad secure : Secure PAD server for use with SSH tunneling
• pad svct : PAD server connection cut-off timer

VPN

IPsec

• ipsec : Show all IPsec commands
• ipsec dpddelay : Set DPD (Dead Peer Detection) delay time
• ipsec dpdmaxfail : Set DPD max fail count
• ipsec dpdretry : Set number of DPD retries
• ipsec enable : Enable/disable IPsec
• ipsec ikeauth : Set IPsec Phase 1 authentication type
• ipsec ikedhgroup : Set IPsec Phase 1 Diffie-Hellman group
• ipsec ikeenc : Set IPsec Phase 1 encryption algorithm
• ipsec ikeexchange : Set IPsec Phase 1 exchange mode
• ipsec ikehash : Set IPsec IKE Phase 1 hash algorithm
• ipsec ikeinitial : Set IPsec Phase 1 initial contact setting
• ipsec ikelifetime : Set IPsec Phase 1 lifetime
• ipsec ikemodecfg
• ipsec ikemyid : Set IPsec Phase 1 Local ID
• ipsec ikepassive : Set IPsec Phase 1 peer role - initiator/responder
• ipsec ikepeerid : Set IPsec Phase 1 Remote ID
• ipsec ikeproposal : Set IPsec Phase 1 Proposal
• ipsec ikerekey : Set IPsec Phase 1 DPD rekey policy
• ipsec ikeverifyid : Verify Remote ID
• ipsec localnet : Set whether to use LAN0 or LAN1 for IPsec subnet
• ipsec loglevel : Set IPsec log level
• ipsec natt : Enable IPsec NAT traversal
• ipsec nattkeepalive : Set NATT keepalive interval
• ipsec psk : Set IPsec pre-shared key
• ipsec remgw : Set IPsec remote gateway IP address
• ipsec remnet : Define IPsec remote subnet(s)
• ipsec remping : Set ping interval to remote tunnel target
• ipsec remtarget : Set IP address of remote target
• ipsec restrict : Define restrictive access policy
• ipsec saauth : Define IPsec ISAKMP phase II authentication algorithm
• ipsec saenc : Define IPsec ISAKMP phase II encryption algorithm
• ipsec salifetime : Define IPsec ISAKMP phase II lifetime
• ipsec sapfsgroup : Define IPsec ISAKMP phase II perfect forward secrecy group
• ipsec show : Show IPsec configuration
• ipsec split : Enable / disable split tunneling

VPNC

• vpnc : Enable VPNC

Man Down Pendant

• mode : Sets serial port(s) connection mode
• pendantreport : Set pendant report
• panicreport : Set pendant panic (PANIC/MPANIC/FPANIC) report
• panicreportack : Set device to send pendant acknowledgment when panic report received
• panicreptype : Set pendant panic report type
• wpan acktype : Man Down Pendant acknowledgement type
• wpan adddev : WPAN accessory add device id, query device id
• wpan delall : WPAN accessory delete all device ids
• wpan deldev : WPAN accessory delete device id
• wpan dist : Configure WPAN Gateway distance report message
• wpan msgtermid
• wpan panid : WPAN accessory set PAN id, query PAN id
• wpan pensrv : WPAN server for remote access to Man Down Pendant devices
• wpan secure : Secure WPAN server for use with SSH tunneling
• wpan stm : Select internal gateway

Diagnostics and Logging

• event dump : Dump the event log file
• ipadr : IP address
• rfstats : Displays various RF statistics
• showconfig : Displays current configuration settings
• showstate : Displays device state
• syslog : System log
• ver : Firmware version

Event Log Configuration

• event add : manually add events to the event log
• event healthinterval : Interval between HEALTH status events
• event logclear : Clear the event log file
• event loglevel : Set the event reporting level
• event minoffline : Set minimum time interval before reporting CELL_ONLINE event
• event report : Set which type of report to use for event reports

Special Features

Geo-Routing

• geort acount : View Geo-Route allowed zone violation counter
• geort c2bin : Convert Geo-Route route lists into CTM200 format
• geort delete : Delete (deactivate) Geo-Routes
• geort enable : Enable/disable Geo-Route
• geort list : View routes being checked by Geo-Route
• geort period : Set how often Geo-Route checks for violation[
• geort rcount : View Geo-Route restricted zone violation counter
• geort report : Set reports used for Geo-Route
• geort th : Set Geo-Route violation threshold
• geort update : Add/update (activate) Geo-Routes

RF Switch

• ctm15x : Command for configuration of protected values
• speedth : Speed threshold for enabling RF module of the device

RFID/Card Reader Support

• mode : Sets serial port(s) connection mode
• cardlistclear : Erase approved ID list from device
• cardlistload : Load approved ID list for swipe card interface
• cardlistsave : Save approved ID list to non-volatile RAM
• cardunlockload : Load a swipe card unlock script to the device
• swipe delay : Set whether to look for valid RTC time before enabling iButton
• swipe gpio : Set iButton GPIO mapping
• swipe idmode : Set how user IDs are parsed by the system before being reported
• swipe idregex : Use regex and grouping to parse the ID to be reported
• swipe ignwindow : Set time after ignition OFF before requiring another swipe
• swipe invoutmask : Set which outputs are toggled when an invalid card is read
• swipe invoutval : Set output values when an invalid card is read
• swipe mode : Set swipe-card interface
• swipe readwindow : Set time after boot to allow reading an ID
• swipe report : Set swipe-card report
• swipe sameiddelay : Set time between identical swipes before they are processed
• swipe valoutmask : Set which outputs are toggled when a valid card is read
• swipe valoutval : Set output values when a valid card is read

FTP Server

• ftp server : Enable/disable ftp server

Garmin PND

• mode : Sets serial port(s) connection mode
• pad clientport : PAD client port number for dialup emulation modes
• pad ip : PAD IP address
• pad mode : PAD mode
• pad port : PAD port number

Installer

• id :installer id
• name :installer name
• vueserver :installer GPS server address
• vuereportnum :installer GPS server report number